|
INCRA
TS-LS Joinery System
(Shown Here with
Table Saw & Two Optional Router
Table Extension
Wings)
Part Number: LS32-TS-WF, LS52-TS-WF,
M-LS32-TS-WF &
M-LS52-TS-WF |
|
|
 |
Now
available in imperial or metric!
The NEW INCRA TS-LS
offers the one thing that every table saw
fence should have, but none of them do, namely,
Automatic Positioning Control. All other table
saws depend on a tape measure and your eyesight
to position your work. That's why all
table saw users are resigned to the fact that
a good cut requires long set-up times and
endless trial and error.
|
|
|
The INCRA TS-LS completely eliminates the need for
these tedious processes by using INCRA'S patented
lead screw technology to position your work instantly
and automatically to within 0.002".
Even better, if you want to repeat a cut, you can
return to any former position in less than 5 seconds
with ZERO repeatability error. This kind of accuracy
and perfect repeatability are luxuries that woodworkers
could only dream about before the INCRA TS-LS. And
because of its structural design, centrally placed
carriage, and optimized side mounted clamping system,
the entire unit virtually welds itself together
into one solid block of steel and aluminum when
locked in place. The result is exceptional strength,
rigidity and stability.
TS-LS Joinery Systems
are available in 32", 52", 810mm and 1230mm
range models. |
 |
|
Spend
more time cutting, less time tapping and
measuring!
Now available in metric,
the LS positioner's patented lead
screw positioning mechanics allow fence
positioning
accuracy of +/- .002" at 1/32"
increments (+/-0.05mm on
1mm increments) across its entire range.
It's essentially
perfect even without the built-in micro
adjust, but the large micro-adjust knob
turns the lead screw against the mating
threads, allowing the fence to be shifted
between incremental steps with .001"
(0.025mm) resolution. The incredible control |
|
| available
completely eliminates the "Tap, tap, tapping"
involved in making small adjustments to a conventional
rip fence. And since the mike is lead screw-based
and reads directly in thousandths of an inch, it's
repeatable as well. This micro adjust is entirely
different from the random, slow-motion knobs used
on rip fences in the past. |
| |
| INCRA's TS-LS
System was one of only two fence systems to
earn top scores for alignment against the
blade and lack of deflection in Wood Magazine's
May 2004 Rip Fence Test. Perfect alignment
relative to the blade is guaranteed by the
system's low friction and by the carriage
lock's tremendous pressure across the sliding
carriage, not unlike a traditional T-square
style rip fences. The fence can be initially
aligned parallel to the miter slot, slightly
"relieved" on the outfeed end, or
anywhere in between. |
 |
|
|
INCRA
TS-LS Table Saw Fence - 52" Range
The 52" (1320mm)-capacity
TS-LS System uses 92"
rails and either a 32" or 810mm
LS Positioner. The standard Mount Unit (LS52-TS)
handles saws measuring 28" or smaller
front-to-rear (along the miter slot). Saws
measuring 28" to 33-1/2" deep can
be accommodated by ordering the TS-LS with
the "XL" Mount Unit (LS52-TS-XL),
which has a longer fence and base support
panel.
|
 |
|
|
Convenience
and Capacity
There are two rail lengths
available: The 32" (810mm)-capacity
TS-LS is based on a 72" Rail length, and the
52" (1320mm)-capacity system uses 92"
Rails. Both systems use the same LS32 Positioner,
and quick-release knobs allow the positioner's base
assembly to be shifted further from the saw blade
on the 52" system's longer rails to achieve
the greater capacitt. The TS Rail Support Legs are
standard equipment on the 52" System.
The quick-release feature allows the positioner's
base assembly to be positioned anywhere along the
length of the rails to access a router table in
any position, and the base assembly can removed
in seconds, giving you total access to the saw's
surface. The quick release also allows the base
assembly to be reversed on the rails to allow about
14" (350mm) of ripping capacity to the left
of the blade. After the fence and base assembly
has been removed from the rails or repositioned,
three pairs of stops on the rails guarantee that
the fence system stays perfectly aligned and calibrated,
time after time. |
|
Will
the INCRA TS-LS fit on my table saw?
The INCRA TS-LS will fit directly on just about
any standard 10" table saw, typically without
any drilling or tapping. There are only two things
you need to check to make sure that it will fit
your saw:
1. The length of miter gauge slot (front-to-back
distance of table). If this measurement is 28-1/2”
or less (standard for most 10" table saws),
the standard INCRA TS-LS will will fit your saw.
If this measurement is between 28-1/2” and
33”, the TS-LS System can be ordered with a
longer fence extrusion and base support panel for
a nominal charge as a substitution for the standard-length
components.
2. The front and rear surfaces of the saw. These
surfaces must be flat and square to the top, with
at least two holes in each surface. Hole locations
and diameter are unimportant because INCRA's universal
rail mounting brackets will work with any hole pattern
and a wide variety of hole sizes.
See the TS-LS
Compatibility Chart for more information regarding
the TS-LS & TS Router Table installations. |
|
 |
Package #1 - Pair of 72" Rails |
| Package
#2 - Base Mount Unit |
| Package
#3 - LS32 Positioner |
| |
|
| |
| TS-LS
Specifications: |
|
| |
 Positioning Range - Right of Blade: 32"
or 810mm Metric |
| |
Positioning Range - Left of Blade: 14",
355mm |
| |
Positioning Accuracy: .002" Over Full
Range |
| |
Repeatability: Return to any former position
in less than 5 seconds with
ZERO repeatability error |
| |
Fence Length: 36" |
|
| |
| INCRA
TS-LS Joinery System - 32" Range consisting
of: |
|
| |
TS-IIIAMOUNT - Base Mount Unit and TS-IIIA
Rip Fence |
| |
RAIL72 - 72" Rails - PAIR |
| |
LS32WFNCSYS - INCRA LS 32" Range Positioner
with split Router Table
Fence Super System |
|
| |
| INCRA
TS-LS Table Saw Fence - 52" Range consisting
of: |
|
| |
TS-IIIAMOUNT - Base Mount Unit and TS-IIIA
Rip Fence |
| |
RAIL92 - 92" Rails - PAIR |
| |
LS32WFNCSYS - INCRA LS 32" Range Positioner
with split Router Table
Fence Super System |
| |
TSLEGS - INCRA TS Rail Support Legs |
|
